The Chandler Limited Mini TG Rack Mixer Expander adds another 16 channels to your Mini Rack Mixer offering a 32-channel recording mixer. The Chandler Limited Mini TG Rack Mixer Expander features transformer balanced, new Chandler Line Amp and discrete amps throughout delivering the classic 60’s and 70’s sound. In total the expander boasts no less than 20 discrete amplifiers and 22 custom wound transformers which combined deliver a whole lot of punch and colour. The Expander differs from the actual mixer by not including the Control Room section and requires the Chandler Limited PSU-2 power Supply to function. FEATURES Expands to 32 channels Speaker 1/2 and external input 2 stereo outputs Full-featured control room section Stereo insert 22 custom-wound transformers Talkback module Channel pan Meter module Provides 20 discrete amplifiers SPECIFICATIONS 19" rackmount Steel construction Weight: 50 lb. (22.7kg) 22 transformers 8 total channels 2 channel line input modules Talkback module Control room monitor panel Master module (4 slot)

The via Fader is a brand new way to connect your 500 series racks and audio gear. This product is more than just 10 or 16 slide faders. Each fader channel has the necessary input and output electronics to allow the via Fader to interface to any balanced, unbalanced, transformer, or transformer-less line level signal. But most importantly... no additional mixer or audio interface is required. With its clean, uncluttered layout, the via Fader can be placed in a convenient desktop location or installed in your 19" rack. This gives you more choices when it comes to the studio layout. Not exclusively for 500 rack systems, the via Fader can be used for external DAW summing or as a line mixer for synths and samplers. In many cases, the via Fader can eliminate the need for a mixing console in your studio. The four via Fader models give you lots of possibilities. Model VF10 Connector Panel All audio connections are located on the bottom/rear of the via Fader chassis. For economy, the rear panel connector legend shows all four models with the connector legend for the Model VF10 shown at the very top.Connect the via Fader to virtually any line level source: balanced, unbalanced, transformer, or transformer-less. The VF10 line inputs and outputs are fully balanced and terminate on DB25 connectors that comply with the Tascam wiring standard. The via Fader has high headroom that will handle balanced signals up to +28dBu.As an added convenience, on the Model VF10 line inputs and outputs 9 and 10 may be accessed with the balanced TRS jacks instead of the DB25 connectors. Included on the bottom panel (not shown on this image) are jumpers that allow you to add 10dB of additional gain to each fader channel.

The via Fader is a brand new way to connect your 500 series racks and audio gear. This product is more than just 10 or 16 slide faders. Each fader channel has the necessary input and output electronics to allow the via Fader to interface to any balanced, unbalanced, transformer, or transformer-less line level signal. But most importantly... no additional mixer or audio interface is required. With its clean, uncluttered layout, the via Fader can be placed in a convenient desktop location or installed in your 19" rack. This gives you more choices when it comes to the studio layout. Not exclusively for 500 rack systems, the via Fader can be used for external DAW summing or as a line mixer for synths and samplers. In many cases, the via Fader can eliminate the need for a mixing console in your studio. The four via Fader models give you lots of possibilities. Model VF10M Connector Panel All audio connections are located on the bottom/rear of the via Fader chassis. For economy, the rear panel connector legend shows all four models with the connector legend for the Model VF10M shown second from the top.Connect the via Fader to virtually any line level source: balanced, unbalanced, transformer, or transformer-less. The VF10M line inputs and outputs are fully balanced and terminate on DB25 connectors that comply with the Tascam wiring standard. The master connectors are also fully balanced and available on TRS jacks.The via Fader has high headroom that will handle balanced signals up to +28dBu. Included on the bottom panel (not shown on this image) are jumpers that allow you to add 10dB of additional gain to each fader channel.